Type DID604

Active chilled beam with four-way air discharge, vertical heat exchanger and condensate drip tray, for grid ceilings with grid size 600 or 625

 

Active chilled beam for heating and cooling, with 2-pipe or 4-pipe heat exchanger, for integration with various ceiling systems. The condensate drip tray is useful if the temperature temporarily falls below the dew point.

  • Preferably for room heights up to 4.20 m
  • High heating and cooling capacity with a low conditioned primary air volume flow rate and low sound power level
  • High comfort levels due to low airflow velocity in the occupied zone
  • Three nozzle variants to optimise induction based on demand
  • Removable induced air grille, fixed with magnets


Optional equipment and accessories

  • Control package
  • Adjustable air control blades to control the airflow
  • Heat exchanger powder-coated black
  • Powder coating in many different colours, e.g. RAL CLASSIC or NCS
  • Application
  • Description

Application

  • Active chilled beams of Type DID604 for the integration into various ceiling systems, preferably for room heights up to 4.20 m
  • Particularly suitable for grid ceilings with grid size 600 or 625
  • 2-pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate
  • Energy-efficient solution since water is used as a medium for heating and cooling
  • Adjustable air control blades (optional) allow for the manual adjustment of the four-way air discharge
  • The condensate drip tray is useful if the temperature temporarily falls below the dew point

Special characteristics

  • Four-way air discharge
  • The vertical heat exchanger with condensate drip tray is useful if the temperature temporarily falls below the dew point
  • Heat exchanger as 2-pipe or 4-pipe system
  • Water connection at the narrow side, Ø12 mm Cu pipe, either with plain tails or with G½" external thread and flat seal

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Attachments

  • Adjustable air control blades

Useful additions

  • Connecting hoses
  • Control equipment consisting of a control panel including a controller with integral room temperature sensor; valves and valve actuators; and compression couplers

Construction features

  • Spigot is suitable for circular ducts to EN 1506 or EN 13180
  • Removable induced air grille, fixed with magnets, secured with safety cables
  • Internal nozzle plate with punched nozzles (non-combustible)
  • Four suspension points for on-site installation (by others)
  • Three nozzle variants to optimise induction based on demand

Materials and surfaces

  • Casing, front frame, nozzle plate, and perforated induced air grille made of galvanised sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Heat exchanger also in black (RAL 9005)
  • Nozzle plate powder-coated black (RAL 9005)
  • Air control blades made of polypropylene, UL 94, flame retardant (V0)

Technical information

  • Function
  • Technical data
  • Quick sizing
  • Specification text
  • Order code
did604

Functional description

Active chilled beams provide centrally conditioned primary air (fresh air) to the room and use heat exchangers for additional cooling and/or heating.

The primary air is discharged through nozzles into the mixing chamber; as a result of this, secondary air (room air) is induced via the induced air grille and passes through the vertical heat exchanger, where it is heated or cooled.

Primary and secondary air mix and are then supplied to the room horizontally through the supply air slots.

did604
did604

 

Active chilled beams of Type DID604, with four-way air discharge and high thermal output, for air-water systems.

For installation flush with the ceiling, preferably in rooms with a height up to 4.20 m.

The units consist of a casing with suspension points, a spigot, non-combustible nozzles, and a vertical heat exchanger with condensate drip tray.

Nozzles in three sizes to optimise induction based on demand.

Special characteristics

  • Four-way air discharge
  • The vertical heat exchanger with condensate drip tray is useful if the temperature temporarily falls below the dew point
  • Heat exchanger as 2-pipe or 4-pipe system
  • Water connection at the narrow side, Ø12 mm Cu pipe, either with plain tails or with G½" external thread and flat seal

Materials and surfaces

  • Casing, front frame, nozzle plate, and perforated induced air grille made of galvanised sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder-coated pure white (RAL 9010) or in any other RAL colour
  • Heat exchanger also in black (RAL 9005)
  • Nozzle plate powder-coated black (RAL 9005)
  • Air control blades made of polypropylene, UL 94, flame retardant (V0)

Construction

  • Powder-coated RAL 9010, pure white, gloss level 50 %
  • P1: Powder-coated in any other RAL colour, gloss level 70 %
  • P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Technical data

  • Nominal length: 600, 1200 mm
  • Length: 593, 598, 618, 623 mm (one tile), or 1193, 1198, 1243, 1248 mm (two tiles)
  • Height: 230 mm
  • Width: 593, 598, 618, 623 mm
  • Primary air spigot, diameter: 123 mm
  • Primary air volume flow rate: 6 – 50 l/s, 22 – 180 m³/h
  • Cooling capacity: up to 1330 W
  • Heating capacity: up to 1250 W
  • Max. operating pressure: 6 bar
  • Max. operating temperature: 75 °C
did604

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.


Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request
Tel.: +7 495 221-5161 | Fax: +7 495 221-5171

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +7 495 221-5161 | Fax: +7 495 221-5171

Contact

We are here for you

Visual contact Visual contact

Please specify your message and type of request
Tel.: +7 495 221-5161 | Fax: +7 495 221-5171

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Visual contact Visual contact

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +7 495 221-5161 | Fax: +7 495 221-5171