Pureline35

Plenum box shorter than front rail, positioned in centre with one horizontal spigot

New design possibilities with white, grey and black air control blades

Horizontal airflow

Slanted airflow

Vertical airflow

TYPE PURELINE35

THE CLEAN SOLUTION FOR SIGNIFICANTLY LOWER CEILING CONTAMINATION

Perfectly integrable slot diffuser with sleek appearance – for discreet installation in the suspended ceiling

Very high comfort due to lower sound power levels and improved temperature and speed reduction
Improved energy efficiency due to lower pressure losses
Simple and fast installation – tool-free fastening of the front rail
New areas of application – including as air curtains for food counters
High flexibility thanks to numerous standard variants

APPLICATION

Application

Type PURELINE35 slot diffusers are used as supply air or extract air devices in comfort zones
Suitable as mixed ventilation system for many applications due to the variety of variants and high flexibility
Discreet integration in suspended ceilings
For rooms up to approx. 4 m in height (bottom edge of finished ceiling)
For suspended ceilings, even with low gaps, due to the low height of the plenum box
One-way or alternate air distribution can be adapted to the structural conditions on site
High induction causes rapid reduction of temperature difference and airflow velocity (with supply air)
For constant and variable volume flow rates
For supply air to room air temperature differences of –10 to +10 K

Special features

Uniform air pattern reduces dirt deposits due to induced compartment air on the ceiling
Horizontal, slanted or vertical supply air distribution through manually adjustable air control blades
Comfortable room climate due to high induction and rapid reduction of temperature differences and airflow velocities
High-quality appearance due to surface-treated extruded aluminium sections with anodised or powder coating according to RAL Classic colour scale
Face plate optimised for maximum volume flow at low sound power levels
Continuous linear arrangement possible for continuous visual appearance

Nominal sizes

LN: 600, 750, 900, 1050, 1200, 1350, 1500, 1650, 1800, 1950 mm
Front rail can also be ordered in mm steps, also in intermediate lengths

DESCRIPTION

Variants

PL35-*: 1 to 4 slots
PL35-*-DF: Only front rail with B00 section and spring clip
PL35-*-DS: Only front rail with B00 section and screw fixing
PL35-*-PB: Only plenum box (for combination with DS)
PL35-*-PF: Combination of front rail and plenum box with fixed connection
PL35-*-SF: Combination of front rail and plenum box with releasable screw fixing
PL35-*-CS: Corner section

Position of plenum box on the front diffuser

Central position of the plenum box
Plenum box left (LE)
Plenum box right (RI)

Plenum box variant

Symmetrical plenum box with horizontal connection (HS)
Symmetrical plenum box with vertical connection (VS)
Asymmetrical plenum box with horizontal connection (HA)

Construction

Diffuser face finish

With anodised finish, E6-C-0, natural colour
P1: Powder-coated RAL 9010, pure white, gloss level 50 %
P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %
P1: Powder-coated in additional RAL CLASSIC colours, gloss level 70 %

Attachments

D: Damper unit for volume flow rate balancing
LS: Lip seal
L: Internal lining
EP: Two end plates
EA: Two end angles

The end plates or end angles of individual devices are already mounted at the factory. Either end plates or end angles can be used as the end piece.

Accessories

EP: Two end plates
EA: Two end angles

For devices that are mounted in a continuous linear arrangement, the end plates or end angles must be ordered separately and installed on site. 2 Alignment plates for connecting the slot diffusers to each other are supplied loose with each slot diffuser without a factory-fitted end piece.

Construction features

Spigot matching round ducting according to EN 1506 or EN 13180
4 suspension points on the plenum box for fixing to be performed by others
Manually adjustable air control blades with detent for defined adjustment of the air distribution
Factory-set air distribution, manually adjustable on site
Spigot with bead for lip seal (only for accessories with lip seal)
Front rail available in mm steps between 600 and 1950 mm
If the front rail is longer than the plenum box, the protruding areas of the front rail are covered at the rear
Plenum boxes only available in nominal lengths
Extract air variant with air control blades optionally possible without air control blades (E0)
The optionally available neck extension in the standard dimensions 30, 55, 80, 105 and 129 mm can be used to compensate for structural conditions

Materials and surfaces

Face plate made of extruded aluminium section
Air control blades made of ABS plastic, to UL94, V-0, flame-retardant
Plenum box made of galvanised sheet steel
End plates and end angles made of aluminium
Lip seal made of Evoprene
Lining of mineral wool and closed cell vinyl foam
Face plate with anodised finish, E6-C-0, natural colour
P1: Powder-coated colour according to RAL Classic
Air control blades similar to RAL 9005, black
G: Air control blades similar to RAL 9006, grey
W: Air control blades similar to RAL 9010, white

Mineral wool

Mineral wool faced with glass fibre fabric on the surfaces in contact with the air, erosion-resistant up to 20 m/s
According to EN 13501, material classification A1, non-flammable
RAL quality mark RAL-GZ 388
Hygienically safe due to high biosolubility, according to TRGS 905 and EU Directive 97/69/EC
Inert to the growth of fungus and bacteria

Standards and guidelines

Sound power level of the air-regenerated noise measured according to EN ISO 5135
Compliant with VDI 6022

Maintenance

Maintenance-free as construction and materials are not subject to wear
Inspection and cleaning according to VDI 6022

Technical information

Function, Technical data, Quick sizing, Specification text, Order code

Schematic illustration of PL35-*-SF

① Face plate or front rail, 1, 2, 3 or 4-slot
② Adjustable air control element
③ Screw fixing
⑥ Neck
⑦ Plenum box
⑧ Suspension lug
⑨ Spigot
Optional
④ End plate
⑤ End angle
⑩ Lip seal
⑪ Damper blade for volume flow rate balancing

Functional description

Slot diffusers allow the supply air of ventilation and air conditioning systems to flow horizontally, obliquely or vertically into the room.

The flow takes place with high induction of indoor air and consequently with a rapid reduction of airflow velocity and temperature difference between supply air and indoor air.

The result is mixed flow air distribution for comfort zones with good room purging and low turbulence levels in the occupied zone.

Type PURELINE35 slot diffusers are factory fitted with manually adjustable air control elements.

Different airflow directions allow adaptation to different local conditions at any time.

Horizontal air distribution takes place with a one-way or alternating flow.

Heating operation with vertical flow is possible, as is a slanted supply air distribution.

The supply air to room air temperature difference can be -10 to +10 K.

A damper unit (optional) enables volume flow rate balancing for commissioning.

To give rooms an aesthetic, uniform look, PURELINE35 diffusers may also be used for extract air.

Nominal length	600 – 1950 mm, in increments of 150 mm
Number of slots	1, 2, 3 or 4
Neck extension	0, 30, 55, 80, 105, 129
Minimum volume flow rate at ∆tz = -10 K	7 l/s or 24 m³/h
Maximum volume flow rate, at LWA ≅ 50 dB(A)	225 l/s or 808 m³/h
Supply air to room air temperature difference	–10 to +10 K

The quick sizing table gives a good overview of the possible volume flow rates and the corresponding sound power levels and differential pressures.

Sizing with our Easy Product Finder design programme will provide the exact values, taking all parameters into account.

The quick sizing table with one spigot applies up to 1200 mm, from 1350 mm and larger two spigots are taken into account.

Slot diffusers of Type PURELINE35 with individually, manually adjustable air control blades and 1, 2, 3 or 4 slots.

Air distribution optionally horizontal alternating, alternating angled, vertical, one-way horizontal left or one-way horizontal right possible.

The slot diffusers can be used for supply or extract air and are intended for installation in the suspended ceiling. Ready-to-install component consisting of the face plate with optional black, grey or white air control blades.

Variants with plenum boxes have 1 or 2 spigots which are arranged horizontally or vertically for symmetrical plenum boxes and horizontally for asymmetrical plenum boxes.

The plenum boxes all have 4 suspension lugs for suspension.

The connection between the face plate and plenum box is made as a fixed or detachable connection.

The spigots are suitable for circular ducts according to EN 1506 or EN 13180. Sound power level of the air-regenerated noise measured according to EN ISO 5135.

Special features

Uniform air pattern reduces dirt deposits due to induced compartment air on the ceiling
Horizontal, slanted or vertical supply air distribution through manually adjustable air control blades
Comfortable room climate due to high induction and rapid reduction of temperature differences and airflow velocities
High-quality appearance due to surface-treated extruded aluminium sections with anodised or powder coating according to RAL Classic colour scale
Face plate optimised for maximum volume flow at low sound power levels
Continuous linear arrangement possible for continuous visual appearance

Materials and surfaces

Face plate made of extruded aluminium section
Air control blades made of ABS plastic, to UL94, V-0, flame-retardant
Plenum box made of galvanised sheet steel
End plates and end angles made of aluminium
Lip seal made of rubber
Lining of mineral wool and closed cell vinyl foam
Face plate with anodised finish, E6-C-0, natural colour
P1: Powder-coated colour according to RAL Classic
Air control blades similar to RAL 9005, black
G: Air control blades similar to RAL 9006, grey
W: Air control blades similar to RAL 9010, white

Mineral wool

Mineral wool faced with glass fibre fabric on the surfaces in contact with the air, erosion-resistant up to 20 m/s
According to EN 13501, material classification A1, non-flammable
RAL quality mark RAL-GZ 388
Hygienically safe due to high biosolubility, according to TRGS 905 and EU Directive 97/69/EC
Inert to the growth of fungus and bacteria

Construction

Diffuser face finish

With anodised finish, E6-C-0, natural colour
P1: Powder-coated RAL 9010, pure white, gloss level 50 %
P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %
P1: Powder-coated in additional RAL CLASSIC colours, gloss level 70 %

Technical data

Nominal lengths: 600 – 1950 mm in steps of 150 mm
Number of slots: 1, 2, 3 or 4
Minimum volume flow rate at ∆tz = –10 K: 7 l/s or 24 m³/h
Maximum volume flow rate, at LWA ≅ 50 dB(A): 225 l/s or 808 m³/h
Supply air to room air temperature difference: -10 to +10 K

Sizing data

V _______________________ [m³/h]
Δp_t _______________________ [Pa]

Air-regenerated noise

L_WA _______________________ [dB(A)]

This specification text describes the general properties of the product. Texts for variants can be generated with our Easy Product Finder design programme.

Order example: PL35-1-S-PF-HS/1200x1200x98/1

Number of slots	1
System	Supply air
Variant	With fixed connection between plenum box and face plate
Plenum box variant	Standard plenum box with horizontal connection
Nominal size	Front rail 1200 mm, plenum box 1200 mm, spigot diameter 98 mm
No. of spigots	1
Damper unit for volume flow rate balancing	Without
Lip seal	Without
Lining	Without
Position of plenum box	Central position
Air pattern	Alternating horizontal
Extended border	Without
End pieces	Without
Surface	Anodised, E6-C-0, natural colour
Colour of air control blades	black

Order example: PL35-2-S-SF-HS/1200x1050x123/2-D-LS-L-LE/AS/B00/EA/P1-RAL 9010/W

Number of slots	2
System	Supply air
Variant	With releasable connection between plenum box and front rail
Plenum box variant	Standard plenum box
Nominal size	Front rail 1200 mm, plenum box 1050 mm, spigot diameter 123 mm
No. of spigots	2
Damper unit for volume flow rate balancing	With
Lip seal	With
Lining	With
Position of plenum box	Left side
Air pattern	Alternating angled
Extended border	With
End pieces	With end angle
Surface	Powder-coated RAL 9010, pure white, gloss level approx. 50 %
Colour of air control blades	white

Order example: PL35-2-E-DF/1200/V/B00/EP/P1-RAL 9006/G

Number of slots	2
System	Extract air
Variant	Diffuser face with extended border and spring clip
Plenum box variant	No plenum box
Nominal size	Diffuser face 1200 mm
No. of spigots	Without
Damper unit for volume flow rate balancing	Without
Lip seal	Without
Lining	Without
Position of plenum box	No plenum box
Air pattern	Vertical
Extended border	With extended border
End pieces	With end plate
Surface	Powder-coated RAL 9006, white aluminium, gloss level approx. 30 %
Colour of air control blades	grey

Order example: PL35-1- -CS/100x100x90

Number of slots	1
Variant	Corner section
Dimensions	Leg dimension E: 100 mm Leg dimension F: 100 mm Angle: 90°
Extended border	Without
Surface	Anodised, E6-C-0, natural colour
Colour of air control blades	Black, similar to RAL 9005

Order example: PL35-2- -CS/150x250x45/B00/P1-RAL 9016/W

Number of slots	2
Variant	Corner section
Dimensions	Leg dimension E: 150 mm Leg dimension F: 250 mm Angle: 45°
Extended border	With
Surface	Powder-coated RAL 9016, gloss level 70%
Colour of air control blades	White, similar to RAL 9010

Variants, Dimensions and weight

Asymmetrically positioned plenum box

End angles on both ends

Nominal length

Nominal length	L₁
Nominal length	mm
600	600
750	750
900	900
1050	1050
1200	1200
1350	1350
1500	1500
1650	1650
1800	1800
1950	1950

Variant

Variant	With extended border
Variant	P
Variant	mm
PL35-1	56
PL35-2	82
PL35-3	109
PL35-4	136

Dimensions [mm]

No. of spigots	Nominal length	L₁	L₃
1	600	600	595
1	750	750	745
1 or 2	900	900	895
1 or 2	1050	1050	1045
1 or 2	1200	1200	1195
2	1350	1350	1345
2	1500	1500	1495
2	1650	1650	1645
2	1800	1800	1795
2	1950	1950	1945

Variant

Variant	B3	B3	H4	H4	R	A	A	O	O
Variant	HS/HA	VS	HS/HA	VS	R	HS/HA	VS	PF-HA	SF-HA
PL35-1	100	138	150	150	126 + Y	140	178	72	64
PL35-2	138	160	180	150	141 + Y	178	200	83	75
PL35-3	176	176	198	150	150 + Y	216	216	94	86
PL35-4	214	214	230	150	166 + Y	254	254	106	97

Neck extension Y = 0 / 30 / 55 / 80 / 105 / 129

Variant

Variant	∅D	C
PL35-1	98/123	50/48
PL35-1	123/138	48/42
PL35-2	138/158	42/50
PL35-2	158/198	50/50

Weights

Variant	Number of slots	kg/m
Diffuser face	1-/2-/3-/4-slot	0,8/1,2/1,6/2,1
Plenum box HS/HA	1-/2-/3-/4-slot	3,3/3,9/4,6/5,2
Plenum box HS/HA+L	1-/2-/3-/4-slot	4,0/4,7/5,5/6,2
Plenum box VS	1-/2-/3-/4-slot	3,7/3,9/4,1/4,3
Plenum box VS+L	1-/2-/3-/4-slot	4,5/4,7/4,9/5,2

Total weight = weight of diffuser face + weight of plenum box

Variant

Variant	Without extended border	With extended border
Variant	P
Variant	mm
PL35-1	35	55
PL35-2	62	82
PL35-3	89	109
PL35-4	116	136

	E	F	W
Min. entry value	100	100	45°
Max. entry value	300	300	175°

Variante

Variant	Without extended border	With extended border
Variant	P
Variant	mm
PL35-1	35	55
PL35-2	62	82
PL35-3	89	109
PL35-4	116	136

Installation examples, Installation details, Commissioning, Basic information and nomenclature

PL35-1/.../B00, installation in continuous ceilings

Anodised, E6-C-0, natural colour

PL plenum box, positioned on the left, in the centre, on the right

Installation and commissioning

Preferably for clear room heights up to 4.0 m
Flush ceiling installation
Duct connection horizontal or vertical
For face plates with shorter plenum boxes and non-active diffusers, there is a slot cover on the rear
For continuous linear arrangement, connect face plates to one another with alignment plates
If necessary, carry out volume flow rate balancing on the damper unit
Suitable fixing material for fixing the slot diffusers must be provided by others

The illustrations are schematic and serve to better understand the installation details.

Volume flow rate balancing

Отрегулируйте положение устройства изменения направления потока воздуха в

области патрубка так, чтобы можно было вставить отвёртку

Volume flow rate balancing

If several slot diffusers are assigned to one volume flow controller, it may be necessary to balance the volume flow rates.

Slot diffusers with plenum box and damper unit (variant -D): The flow adjustment damper can also be operated when the face plate is mounted.

Principal dimensions

ØD [mm]

Outer diameter of the spigot

C [mm]

Length of the spigot

m [kg]

Weight

L₁ [mm]

Length of front rail

L₃ [mm]

Length of plenum box

P [mm]

Width of slot section

H₄ [mm]

Height of plenum box

B₃ [mm]

Width of plenum box

Nomenclature

L_WA [dB(A)]

Sound power level of the air-regenerated noise, A-rated

V [m³/h] and [l/s]

Volume flow rate

Δt_z [K]

Supply air to room air temperature difference, supply air temperature minus room temperature

Δp_t [Pa]

Total differential pressure

Downloads

product information

Print page Pureline35

TYPE PURELINE35

THE CLEAN SOLUTION FOR SIGNIFICANTLY LOWER CEILING CONTAMINATION

APPLICATION

DESCRIPTION

Technical information

Function, Technical data, Quick sizing, Specification text, Order code

Variants, Dimensions and weight

Installation examples, Installation details, Commissioning, Basic information and nomenclature

Downloads

product information

Print page Pureline35